SZRCR-NTU02-486900
軟件分為波形顯示，電機運行參數等幾個部分。
下面介紹一下各個部分的功能和作用。
波形顯示:一共有4個通道，分別用4種顏色表示。顏色和
電機運行參數內的字體顏、色相同。即:藍表示電流，綠表示輸
出的脈寬，紅表示當前轉速，黑表示電壓。
電機運行參數:表示電機運行的實時數據。
驅動器設置參數:顯示驅動器的撥碼開關，和方向使能設置。
如果是modbus模式，此欄無效。
驅動器運行狀態:此欄會顯示驅動器的報警狀態，如果沒有
報警會顯示運行正常。
Modbus控制參數:此欄內的參數是驅動器內部的參數，如果
要修改這些參數，必須先對modbus使能寫1。具體的參數含義參考
寄存器說明。
Modbus讀取:此欄可設定驅動器的地址，讀取驅動器數據的
周期，和是否讀取。
Modbus發送:此欄用于修改驅動器參數，首先選定參數類型,
再設定好參數數據，然后點發送即可。

SZRCR-NTU02-486900
The software is divided into several parts, such as waveform display, motor operating parameters, etc.
The following describes the functions and functions of each part.
Waveform display: there are 4 channels in total, which are represented by 4 colors respectively. Color and
The font color and color in the motor operating parameters are the same. Namely: Blue indicates current, green indicates input
The output pulse width, red indicates the current speed, and black indicates the voltage.
Motor operation parameters: real time data of motor operation.
Driver setting parameters: display the dial switch of the driver and the direction enabling setting.
In case of Modbus mode, this column is invalid.
Drive running status: this column will display the alarm status of the drive. If there is no
The alarm will show normal operation.
Modbus control parameters: the parameters in this column are internal parameters of the driver. If
To modify these parameters, you must first write 1 to the Modbus enable. Specific parameter meaning reference
Register description.
Modbus read: this column can set the address of the drive and read the
Cycle, and whether to read.
Modbus send: this column is used to modify drive parameters. First, select the parameter type,
Then set the parameter data and click send.