JANCD-MTV01-485488
雙電源開關控制器可以對兩路供電電源(常用電源和備用電源)進行實時檢測。當其中一路電源(常用電源或備用電源)斷電或是缺相時，控制器就會發出切換命令，使供電電源自動切換到另一路電源(備用電源或常用電源)上，以此來保障供電的連續性。控制器的工作方式主要有自動方式和手動方式兩種。
(1)自投自復模式：控制器對兩路電源進行監控，當兩路電源都正常工作時，則負載由常用電源供電；當常用電源發生故障(斷電或缺相)時，控制器發出切換命令使電源自動切換到備用電源，此時負載由備用電源供電；當常用電源恢復正常時，控制器再次發出切換命令使負載供電由備用電源返回到常用電源。
(2)自投不自復模式：其工作方式和自投自復類似，但只有當備用電源也出現故障時才自動返回到常用電源，否則將一直由備用電源給負載供電。
(3)電網-發電機模式：當常用電源發生故障時，控制器輸出發電機啟動命令，經短暫延時后斷開常用電源，此時負載由發電機供電；當常用電源恢復正常時，控制器輸出發電機停機命令同時電源自動切換到常用電源上，負載返回到由常用電源供電模式。
在手動模式下，電源不能自動切換而需要人為操作，主要有常用電源供電、備用電源供電和斷電再扣方式。

JANCD-MTV01-485488
Dual power switch controller can detect two power supplies (common power supply and standby power supply) in real time. When one of the power supplies (common power supply or standby power supply) is powered off or lacks phase, the controller will issue a switching command to automatically switch the power supply to the other power supply (standby power supply or common power supply) to ensure the continuity of power supply. The working mode of the controller mainly includes automatic mode and manual mode.
(1) Automatic switching and automatic recovery mode: the controller monitors the two power supplies. When both power supplies work normally, the load is powered by the common power supply; When the common power supply fails (power failure or phase loss), the controller sends a switching command to automatically switch the power supply to the standby power supply. At this time, the load is powered by the standby power supply; When the common power supply returns to normal, the controller sends a switching command again to return the load power supply from the standby power supply to the common power supply.
(2) Automatic switching without automatic recovery mode: its working mode is similar to that of automatic switching and automatic recovery, but it will automatically return to the common power supply only when the standby power supply also fails, otherwise the standby power supply will always supply power to the load.
(3) Grid generator mode: when the common power supply fails, the controller outputs the generator start command, and after a short delay, the common power supply is disconnected. At this time, the load is powered by the generator; When the common power supply returns to normal, the controller outputs the generator shutdown command, and the power supply is automatically switched to the common power supply, and the load returns to the power supply mode by the common power supply.
In the manual mode, the power supply cannot be switched automatically but needs to be operated manually. There are mainly common power supply, standby power supply and power failure and re deduction.